|
BR-100 industrial roller doors
Roller doors have the Technical Approval ITB No. AT-15-4373/2000
q LIST OF QUESTIONS to let you order properly a BR-100 roller door
Overall dimensions
In Fig. 2 required mounting dimensions indispensable for the correct door selection and execution are shown
Minimum widths of side space required to fix the door W1 min and W2 min are given in Fig. 3.
For the correct door fixing, a doorhead is indispensable for mounting the console, minimum doorhead height depends on the opening height. Required doorhead heights for doors type HANDLOPOL BR-100 are in table 1. Table 1
Full driveway clearance As a standard, when the door has been fully opened there are about 2 coat sections left in the opening clearance, thus the driveway height is about 200 [mm] smaller (figure 4).
On request it is available to make the door higher so as the driveway height is equal to the opening height. Then the required minimum doorhead height is appropriately (see the table given below): Table 2
If you order the higher version of the door, state "yes" in the column "full driveway height". If not filled in, it indicates the door in standard version. Glazed sections Sections in glazed version may be used in doors type HANDLOPOL BR-100 in order to light better the room. These sections are not provided with heat insulation. Examples of placing sections with windows are given in the following figures.
State the number of glazed sections in the order and show in the enclosed drawing at what height from the floor level they are to be fixed in the door coat (example of a drawing illustrating the way of glazed sections location marking is given below), if you do not wish glazed sections, put sign "-" in the column. It is not recommended to use glazed sections in the upper part of the door, in the distance smaller than 1 m from the doorhead.
Is there an additional entrance When mounting BR-100 doors an additional entrance to the garage is required. Write "yes" or "no" on the order form in the column "is there an additional entrance". If there is no such entrance it is not available to mount such a door. Colour AW aluminum sections are made in standard colours: RAL 5012 (blue); RAL 8019 (dark brown) and RAL 9010 (white). As a standard sections and guides of a given door are made in the same colour. Wall Depending on the execution HANDLOPOL BT-100 roller doors may be fixed to the walls made of reinforced concrete (B), brick walls (C) or walls made of steel frames (S). In the order give the exact data concerning the wall execution as well as the wall thickness. The room dedicated to the mounting has to be completely finished (walls plastered, floor finished), the walls cannot have the traces of defects of execution. The room has to be dry and free from chemicals harmful for paint coats. Too much dampness in the object may have a negative impact on the door operation and its durability, and even lead to the door damage. Electric control HANDLOPOL BR-100 roller doors as a standard are equipped with an electric drive with a three-phase compact motor operator operated manually from the inside of the room. On request it is available to provide a switch-off for the key fixed outside the room. Additional equipment of the electric drives may be remote control using transmitters and an automatic door closing. Photocells are installed as a standard in each case of using remote control or automatic closing, protecting from the door closing when there is an obstacle in its clearance. Automatic closing causes that the door is automatically closed after a determined time set in the controller. Write "yes" on the order form in the column "automatic closing" in the case of ordering a control with the automatic closing.
Specify the
number of additional transmitters (there are two in standard) in the order
when you order the remote control. Write on which side of the door, looking
from the room inside, the supply source is (left - L or right -
P). Information concerning the supply source
position determines on which side the motor operator driving the door is to
be installed, In BR-100 industrial doors it is recommended to apply the light signalling letting to know if the door is open or closed. The signalling device sends green light if the door is open, whereas when the door is closed or in motion the signalling device sends red light. Write "yes" or "no" on the order form. Optionally, on request it is available to install an optical safety bar. If you wish to order the safety bar, state it in the column "NOTES" on the order form. When the electric control is damaged or the power supply cut off it is possible to open the door manually using a mechanism driven with a hand-crank, fixed at the motor operator driving the door at a height approximately equal to the door height. In doors driven with AF-170 or AF-250 motor operators as a standard the crank length matches the door height. On the other hand, there is no such a possibility in doors driven with AF-450; that is why, taking into account a substantial door height and possible emergency of opening the door, it is recommended that in each case there be a ladder fixed to the wall on the side of the motor operator driving the door, or free room left making possible to put a stepladder. Write possible additional requirements concerning the door execution on the order form in the column "NOTES". Fig. 7 shows a BR-100 roller door and specifies the basic sub-assemblies of this door.
Fig. 7 BR-100 roller door
Colours according to RAL palette
|
![Textruta: Opening width [mm]](BR_100-filer/image007.gif){kind=small}
![Textruta: Opening height [mm]](BR_100-filer/image009.gif){kind=small}
